Imprint   Area map   Contact   Sitemap   Fuchs worldwide   Deutsch
			About usInvestor RelationsNewsCorporate GovernanceProductsMotorsportServiceJobs & Careers
				Home > Products > Product Review > Metalforming Lubricants > RENOFORM 702-461-AV >
	Product Review Engine and Gear Oils Mould Release Agents Metalworking Fluids Metalforming Lubricants RENOFORM VB 360 RENOFORM MBO 236 RENOFORM HBO 962/2 RENOFORM FW Series RENOFORM 702-461-AV RENOFORM 569 RENOFORM 519-HT RENOFORM 51-DO RENOFORM 457 RENOFORM 319-IS RENOFORM 1665/1 TRENOIL S Series TRENOIL T Series TRENOIL SP Series Corrosion Preventives Quenching Oils Greases Industrial Lubricants Rapidly Biodegradable Lubricants Other products and services Publication Exhibitions FUCHS for REACH - The new EU chemical law EURO PI
				RENOFORM 702-461-AV Cold forming lubricant, chlorine-free, dual purpose RENOFORM 702-461-AV is a chlorine-free, EP cold forming lubricant which can perform many difficult cold forming operations and is recommended as extrude oil for spark plug bodies. RENOFORM 702-461-AV is especially formulated to be non-corrosive to copper and copper alloys. This means that it can be used on both sides of the machine, the die side and the machine lubricant side. Two important advantages are: It ends the problem of contaminating the machine lubricant with die lubes which can be corrosive to non-ferrous bearings.  Dilution of the die lube by machine lubes causes changes in viscosity and EP content of the die lube. When RENOFORM 702-461-AV is used in both ends of the machine, this will not occur and potential tooling problems will be avoided. Benefits of using RENOFORM 702-461-AV: Provides EP lubrication to prevent metal pick-up on tooling  Suitable for a wide variety of cold forming operations  Dual purpose - can be used as both a die lubricant and a machine lubricant  Good heat removal properties  Easily cleaned in most conventional cleaning systems  Non hazardous to use - contains no toxic ingredients Application: Die Lubricant: Normally used as supplied. Can be applied directly to the wire or rod on small one and two die headers. Should be flowed directly on the dies and punches on large headers or parts formers. Can be diluted with blending oil for less difficult operations. Machine Lubricant: Always use as supplied. Typical Physical & Chemical Characteristics Properties Unit Value Norm Test Density at 15 °C Kg/l 0.960 ASTM D 1298 Colour   >8.0 ASTM D 1500 Viscosity at 40 °C mm²/s 98 ASTM D 445 Flash point COC °C 148 ASTM D 92 Pour point °C 0 ASTM D 97 Copper corrosion / 3 h - 20 °C degree of corr. 1 a ASTM D 130 Copper corrosion / 24 h - 20 °C degree of corr. 1 a ASTM D 130 Copper corrosion / 3 h - 50 °C degree of corr. 1 a ASTM D 130 Copper corrosion / 24 h - 50 °C degree of corr. 1 a ASTM D 130 Copper corrosion / 3 h - 100 °C degree of corr. 1 b ASTM D 130 Copper corrosion / 24 h - 100 °C degree of corr. 1 b ASTM D 130 Four ball test / welding load N 8000 ASTM D 2783 Reichert wear test mm² 4.0 FLP* FLP* = FUCHS Laboratory Procedure   Disclaimer of Liability	Latest News   Press Release of Dec. 9, 2008   Interim Report for the first         nine months and third quarter   Financial Market Conference   Annual Report 2007   Share buy back program   New Research Reports Dates  Financial Calendar March 27, 2009 Balance sheet press conference, Mannheim Motorsport FUCHS EUROPE SCHMIERSTOFFE