ANTICORIT OHK

Home > Products > Product Review > Corrosion Preventives > ANTICORIT OHK >


Product Review

	Engine and Gear Oils

	Mould Release Agents

	Metalworking Fluids

	Metalforming Lubricants

	Corrosion Preventives

		ANTICORIT RP4107 S

		ANTICORIT PL3802 LV

		ANTICORIT OHK

		ANTICORIT MKR

		ANTICORIT DFW

		ANTICORIT DFO

		ANTICORIT DF

		ANTICORIT BW 366

		ANTICORIT 6120/42

		ANTICORIT 5012 S

		ANTICORIT 03 W-C


	Quenching Oils

	Greases

	Industrial Lubricants

	Rapidly Biodegradable Lubricants

	Other products and services



Publication

Exhibitions

FUCHS for REACH - The new EU chemical law

EURO PI

ANTICORIT OHK

Corrosion Protection Concentrate

ANTICORIT OHK is a corrosion protection concentrate principally designed for use as a dilution in solvents or low viscosity oils. White spirits and, if the application machinery permits, chlorinated hydrocarbons can be used as solvents.

If forms a clear solution in all solvents and leaves a highly viscous, oily, non-resinating protective film on components.

ANTICORIT OHK displays the following features:

Excellent corrosion protection for ferrous and non-ferrous metals even if the film is extremely thin

Protects against fingerprint (hand perspiration) corrosion

Dewatering effect

Good lubricity

Highly economical - a little goes a long way!

Removable with neutral or alkaline water-based cleaners.

Characteristics:

Properties	Unit	Value	Test method
Colour		5	ASTM D 1500
Flashpoint	°C	185	ASTM D 92
Density at 15 °C	kg/l	0.932	ASTM D 1298
Viscosity at 40 °C	g/m²	92	ASTM D 445
Viscosity at 50 °C		51	ASTM D 445
Dewatering, 10 % solution
in white spirit after 3 minutes	%	75	FLP-W 3 *)
Neutralization number	mgKOH/g	0.5	ASTM D 974

*) FLP = FUCHS Laboratory procedure

1. Corrosion Protection Data

Corrosion protection test according to VTL 8030-015, 30 % in white spirit, flashpoint 40 °C (determination of changes in weight and visual evaluation of the surface).

Ms + 0.9 mg, no visual change
Zn + 0.4 mg, no visual change
Mg + 1.1 mg, no visual change
Al + 1.2 mg, no visual change
Steel + 0.7 mg, no visual change
Pb - 0.9 mg, no visual change

2. Corrosion Protection Values

30 % ANTICORIT OHK in white spirit, flashpoint 40 °C; film weight 1.3 g/m²

	CK 22	RRSt. 1405	Test method
Humidity cabinet	500 h	300 h	ASTM D 1748
Condensation climate	50 cycles	50 cycles	50 017 KFW
Salt spray test	400 h	240 h	FLP-K 19 *)
Salt spray test	192 h	50 h	ASTM B 117

*) FLP = FUCHS Laboratory procedure

3. Hand Perspiration Tests

OK SKF-AV-D-25
OK MIL-C 150740
OK BOSCH-N 42AP320

Dipped Film Weights (with white spirit, -flashpoint 40 °C)
10 % ANTICORIT OHK 0.25 g/m²
30 % ANTICORIT OHK 1.3 g/m²
50 % ANTICORIT OHK 3.3 g/m²
70 % ANTICORIT OHK 7.8 g/m²

Application:
ANTICORIT OHK can be applied by all commonly-used methods after dilution with solvents. The most practical method of application is dipping.

If sealed in the original container ANTICORRIT OHK can be stored for min. 5 years at 5-40 °C.

Use of ANTICORIT OHK in other fluids:

Specific corrosion protection requirements of metal-working fluids (cutting oils, grinding oils, drawing compounds) can be met by adding 2-4 %.

ANTICORIT OHK is freely soluble even in neat metal-working fluids.

ANTICORIT OHK is ideally suited for oiling components after solvent degreasing. Good results can be achieved by adding up to 5 %.

ANTICORIT OHK in ready-to-use form:

The following ready-to-use versions of ANTICORIT OHK are available:

ANTICORIT	Concentration	Solvent
OHK 230	30%	White spirit, flashpoint 40 °C
OHK 320 A	20%	Low-aromatic white spirit, flashpoint 63 °C
OHK 360 A	60%	Low-aromatic white spirit, flashpoint 63 °C
OHK 380 A	80%	Low-aromatic white spirit, flashpoint 63 °C

Furthermore, ANTICORIT OHK is also available in handy 400 ml spray cans. The propellant is naturally free of FUCH’s – to protect the environment.

Disclaimer of Liability