RENOLIN B

Home > Products > Product Review > Industrial Lubricants > RENOLIN B >


Product Review

	Engine and Gear Oils

	Mould Release Agents

	Metalworking Fluids

	Metalforming Lubricants

	Corrosion Preventives

	Quenching Oils

	Greases

	Industrial Lubricants

		RENOLIN ZAF D

		RENOLIN ZAF B

		RENOLIN UNISYN CKC

		RENOLIN MR

		RENOLIN HL

		RENOLIN CKC

		RENOLIN B HVI

		RENOLIN B

		RENISO Refrigeration Oil


	Rapidly Biodegradable Lubricants

	Other products and services



Publication

Exhibitions

FUCHS for REACH - The new EU chemical law

EURO PI

RENOLIN B

High Quality HM Hydraulic Oils and CKC Lubricating Oils

Diagram

High Quality HM Hydraulic Oils and CKC Lubricating Oils

The function and operational reliability of hydraulic systems depends largely on the quality of the hydraulic fluids used which, apart from transfering forces, must also seal, cool and lubricate. Because hydraulic oils are subject to a variety of stresses, they must fulfil a number of requirements. These must be maintained throughout the service life of the oil and must help combat the formation of undesirable reaction by-products. The RENOLIN B series of oils are based on highly ageing resistant solvent raff inates and fulfill, and in many points surpass, the minimum requirements made on HM hydraulic oils according to ISO 6743-4.

The RENOLIN B series of oils offer the following advantages:

Good EP properties and thus protection against wear

Good viscosity-temperature behaviour

Excellent oxidation stability and resistance to ageing

Excellent corrosion protection

Rapid air release and low foaming

Good demulsification characteristics

Good elastomer compatibility

Application:

The RENOLIN B series of oils are not just high grade hydraulic oils. They are also excellent CKC lubricating oils according to ISO 6743-6 which can be used for numerous applications such as gearboxes and bearings.

RENOLIN		B 3	B 5	B 10	B 15	B 20	B 30
acc. to ISO 6743-4		HM 10	HM 22	HM 32	HM 46	HM 68	HM 100
acc. to DIN 51 502		HLP 10	HLP 22	HLP 32	HLP 46	HLP 68	HLP 100
Characteristics	Unit							Test method
Colour		1	1	1	1.5	2	2.5	ASTM D 1500
Kinematic viscosity
at 40 °C	mm²/s	10	22.4	32	47	67	100	ASTM D 445
at 100 °C	mm²/s	2.5	4.4	5.6	7.1	8.6	11	ASTM D 445
Viscosity index		61	105	114	109	99	94	ASTM D 2270
Density at 15 °C	kg/l	0.85	0.865	0.88	0.88	0.882	0.888	ASTM D 1298
Flash point, Cleveland open cup	°C	160	163	188	210	224	232	ASTM D 92
Pour point	°C	- 27	- 30	- 27	- 27	-24	- 21	ASTM D 97
Neutralization number	mg KOH/g	0.3	0.3	0.3	0.3	0.3	0.3	ASTM D 974
Saponification number	mg KOH/g	0.6	0.6	0.6	0.6	0.6	0.6	ASTM D 94
Oxide ash	% mass	0.2	0.2	0.2	0.2	0.2	0.2	ASTM D 482
Water content	% mass	not traceable	not traceable	not traceable	not traceable	not traceable	not traceable	ASTM D 95
Insolubles	% mass	not traceable	not traceable	not traceable	not traceable	not traceable	not traceable	DIN 51 592
Demulsification	min	15	15	15	15	15	15	DIN 51 599
Air release at 50 °C	min	1	3	6	7	8	16	ASTM D 3427
Foaming,
seq. I	ml	35/0	5/0	20/0	10/0	20/0	10/0	ASTM D 892 seq. I-III
seq. II	ml	10/0	10/0	20/0	40/0	30/0	30/0	ASTM D 892 seq. I-III
seq. III	ml	35/0	5/0	20/0	10/0	20/0	10/0	ASTM D 892 seq. I-III
Copper corrosion	degree of corr.	1a-100A24	1a-100A24	1a-100A24	1a-100A24	1a-100A24	1a-100A24	ASTM D 130
Rust prevention		pass A	pass A	pass A	pass A	pass A	pass A	ASTM D 665
FZG mechanical gear rig test	load stage	12	12	12	12	12	12	DIN 51 354-2
Vickers vane pump test, loss of mass
on ring	mg	< 120	< 120	< 120				IP 281
on vanes after 250 h	mg	< 30	< 30	< 30				IP 281
Effect on SRE-NBR 1 seal material acc. to DIN 53 538-1 at 100 °C +/– 1 °C after 7 days +/– 2 hours, relative volume change
change in Shore A	%	15	7	5	5	5	5	DIN 53 521 together with DIN 53 505
hardness	Shore	- 2	- 1	- 1	- 1	- 1	- 1	DIN 53 521 together with DIN 53 505

Disclaimer of Liability