PLANTOHYD N

Home > Products > Product Review > Rapidly Biodegradable Lubricants > PLANTOHYD N >


Product Review

	Engine and Gear Oils

	Mould Release Agents

	Metalworking Fluids

	Metalforming Lubricants

	Corrosion Preventives

	Quenching Oils

	Greases

	Industrial Lubricants

	Rapidly Biodegradable Lubricants

		PLANTOHYD S

		PLANTOHYD N

		PLANTOGEAR S


	Other products and services



Publication

Exhibitions

FUCHS for REACH - The new EU chemical law

EURO PI

PLANTOHYD N

Environmentally Friendly HETG Hydraulic Fluids and Lubricating Oils Based on Vegetable Oils

Diagram

Environmentally Friendly HETG Hydraulic Fluids and Lubricating Oils Based on Vegetable Oils

It has been recognized for a number of years now that the use of mineral oil-based lubricants poses certain environmental risks. Leakages, emissions and spillages when handling gear and lubricating oils lead to direct pollution of the surroundings and thus the environment. This fact led FUCHS to develop rapidly biodegradable lubricants based on vegetable oils and synthetic esters.

The PLANTOHYD N series of oils are based on vegetable oils. They represent an environmentally friendly alternative to mineral oil-based hydraulic oils and can be classified as HETG fluids according to ISO/CD 6743-4.

The advantages of PLANTOHYD N are:

Rapidly biodegradable (greater 90 % within 14 days according to CEC-L-33-A-93)

German Water Hazard Class WGK 0, i.e. generally not hazardous for water

Non-toxic, physiologically harmless

Free of heavy metals

Excellent viscosity-temperature behaviour because of their high natural VI

Excellent anti-wear properties

Extremely shear-stable Rapid air release

Minimal foaming

Insoluble in water

Good demulsibility characteristics

Applicable at tank temperatures ranging from - 27 °C to +70 °C

PLANTOHYD N products are fully compatible with all materials usually found in hydraulic systems. The base fluids used in these products are non-toxic. The fluids are free of heavy metals and chlorinated compounds.

Application:

PLANTOHYD N hydraulic oils can be used universally in all hydraulic and general lubricating systems. These pro- ducts should always be used whenever there is a danger of soil or water pollution following a leak or spillage. The greatest potential for such occurrences are in the construction, water, agricultural and forestry industries. The high viscosity index of PLANTOHYD N products give them multigrade characteristics.

We recommend that the miscibility and compatibility of these products with mineral oil-based hydraulic oils should be checked on a case-by-case basis. As stated in ISO/CD ECO, residual quantities of mineral oil should be kept to a minimum by flushing prior to refilling. Compatible internal finishes on tanks should be selected. Paint finishes which are not 2-part epoxy systems can display poor resistance to mineral oil as well as vegetable oils. In general, we recommend the use of stainless steel tanks. "Free" metals, e.g. tin from soldered joints or zinc from galvanized components should be avoided if possible. Filter systems should also be compatible with vegetable oils.

The powerful cleaning effect of these fluids can dislodge large amounts of dirt and contaminants and this can, in turn, shorten the life of filters. System filters should be cleaned or changed after about the first week of use with PLANTOHYD N. The ISO/CD ECO guidelines should also be observed. To maintain optimum reliability, any water which has collected in systems which have been shut-down for longer periods should be drained. Water or moisture problems can be reduced if filtering and drying equipment is fitted to tank breathers. According to ISO/CD ECO, water content during use should be kept below 0.1 %.

Our application engineers will be glad to advise you on:

Experiences with these products

Application possibilities

Material compatibility

Change-over procedures

and service facilities regarding PLANTO products.

Typical data:

PLANTOHYD		32 N	46 N	68 N
Hydraulic oil type acc. to ISO/CD 6743-4 and VDMA 24 658		HETG 32	HETG 46	HETG 68
Characteristics	Unit				Test method
Colour		1	1	1	ASTM D 1500
Kinematic viscosity
at 40 °C	mm²/s	31.6	48.6	69.8	ASTM D 445
at 100 °C	mm²/s	7.4	10.6	13.9	ASTM D 445
Viscosity index		213	215	207	ASTM D 2270
Density at 15 °C	kg/l	0.921	0.924	0.927	ASTM D 1298
Flash point, Cleveland open cup	°C	>270	>270	>270	ASTM D 92
Pour point	°C	– 39	– 36	– 36	ASTM D 97
Copper corrosion	degree of corr.	1a-100A3	1a-100A3	1a-100A3	ASTM D 130
Rust prevention		pass A	pass A	pass A	ASTM D 665
FZG mechanical gear rig test	load stage	> 12	> 12	> 12	DIN 51 354-2

Disclaimer of Liability